Tuesday, July 9, 2013
2500W Phase Control
This circuit controls resistive and inductive loads up to 2,500W. Its main functional device is an integrated phase control circuit - Siemens TLE3103. It contains its own power supply, a zero voltage crossing detector circuit and a logic driver. An additional feature is the low voltage input to enable/disable triac firing enabling/disabling the logic driver. The function is as follows: pin13 TLE3103 open (floating), trigger output active, tied to ground trigger output disabled.
2500W Phase Control Circuit diagram

An UP and a DOWN button control a 32-step digital potentiometer (IC2, AD5228) via the debouncer IC1 (MAX6817). The potentiometer has a power on reset pin which might be tied to ground causing the potentiometer to start at midscale, or to VCC causing it to start at zero scale. The desired function is selectable using jumper JP1. The triac (capable of driving 40A loads) is a bit overkill for the desired power but the BTA41 has an isolated body and therefore handling of the board under voltage is less dangerous as it is with phase on the package. The circuit uses a 68μH inductance, but this might be replaced with a 100 resistor, then replacing the inductance C5 should have a value of 47nF.
2500W Phase Control Circuit diagram

LTC2990 System Monitoring IC
Using LTC2990 integrated circuit you can design a very simple monitoring system to monitor system temperatures, voltages and currents. Through the I2C serial interface, the device can be configured to measure many combinations of internal temperature, remote temperature, remote voltage, remote current and internal VCC. The internal 10ppm/°C reference minimizes the number of supporting components and area required. Selectable address and configurable functionality give the LTC2990 flexibility to be incorporated in various systems needing temperature, voltage or current data.
Bellow you can see some ideas how to use the LTC2990 I2C Temperature, Voltage and Current Monitor Ic in your electronic projects .
You can use LTC2900 IC for electronic projects like :motor protection , fan temperature alarm , battery monitoring , liquid level sensing and many other projects .
Bellow you can see some ideas how to use the LTC2990 I2C Temperature, Voltage and Current Monitor Ic in your electronic projects .
You can use LTC2900 IC for electronic projects like :motor protection , fan temperature alarm , battery monitoring , liquid level sensing and many other projects .


Simple OBD Vehicle Protection
vehicle immobilisers are fitted as standard to modern cars and heavy goods vehicles. Anti-theft mechanisms have become more sophisticated but so have the methods employed by crooks. Nowadays once the thief has gained access to a vehicle they will most likely use an electronic deactivation tool which seeks to disable the immobiliser, once this has been accomplished a blank transponder key/card can be used to start the engine. In many cases communication with the immobiliser is made using the OBD-II diagnostic connector.
Although the OBD-II protocol itself does not support the immobiliser, the vehicle manufacturer is free to use the interface as neces-sary for communication, either the standard OBD-II signals or unused pins in the OBD-II connector (i.e. those undefined in the OBD-II standard). Using one of these pathways the immobiliser can usually be electronically disabled.
OBD Vehicle Protection Circuit Diagram
This may be unsettling news for owners of expensive vehicles but when professional car-thieves call, armed with the latest OBD-II hacking equipment this simple low-cost low-tech solution may be all that you need. The idea is ver y simple: if all connections to the OBD-II connector are disconnected there is no possibility for any equipment, no matter how sophisticated to gain access via the vehicle’s wiring.
The OBD-II connector is usually locate d underneath the dashboard on the passenger side; once its wiring loom has been identified a switch can be inserted in line with the wires. The switch should be hidden away some-where that is not obvious. In normal opera-tion you will be protected if the vehicle is run with the wires to the socket disconnected. Make sure however that you throw the switch reconnecting the socket before you next take the vehicle along to a garage for servicing or fault diagnosis.
The diagram shows the ISO K and ISO L wires switched. To cover all bases it is wise for every wire to the socket is made switchable except the two earth connections on pins 4 and 5 and the supply voltage on pin 16. Almost ever y vehicle manufacturer has their own method of vehicle immobilisation, by disconnecting every wire it ensures that no communication is possible (even over the CAN bus). Now the innermost workings of your vehicle will be safe from prying eyes. When a hacker plugs in a deactivation tool it will power up as normal but probably report something like ‘protocol unrecognised’ when any communication with the OBD port is attempted.
Author : Florian Schäffer - Copyright: Elektor
Monday, July 8, 2013
Zener Diode Tester Schematic
Using electronic scheme below can be designed a zener diode tester using few electronic parts. Using this zener tester and a multimeter can be measured and determined with a high precision threshold voltage of a zener diode.Zener voltage can be read with a DC voltmeter connected in parallel with zener diode.
Zener Diode Tester Circuit Schematic Diagram

If contact S1 is closed, the resistance R1, T1 and Zener diode current flow. Base transistor T1 is connected to power supply trough the R4, so the transistor conducts.
Zener current is equal to the ratio of base-emitter voltage of Q2 and the resistance value R1. With a supply voltage of 25 volts at the actuation keys S1-S3, the current through zener diode take values of about 2.2,6 and 22mA. Resistances R2 and R3 or a combination of R1, R2, R3 can be connected in place of R1 with S2-S3 so that through the zener diode constant current flow.
Electrical Isolation For I2C Bus
When the SDA (Serial DAta) lines on both the left and right lines are 1, the circuit is quiescent and optoisolators IC1 and IC2 are not actuated. When the SDA line at the left becomes 0, current flows through the LED in IC1 via R2. The SDA line at the right is then pulled low via D2 and IC1. Optoisolator IC2 does not transfer this 0 to the left, because the polarity of the LED in IC2 is the wrong way around for this level. This arrangement prevents the circuit holding itself in the 0 state for ever. As is seen, the circuit is symmetrical. So, when the SDA line at the right is 0, this is transferred to the left. The lower part of the diagram, intended for the SCL (Serial CLock) line, is identical to the upper part.
Electrical Isolation For I2C Bus Circuit Diagram
Resistors R1, R4, R5, and R8, are the usual 3.3 kΩ pull-up resistors that are obligatory in each I2C line. If these resistors are already present elsewhere in the system, they may be omitted here. The current drawn by the circuit is slightly larger than usual since the pull-up resistors are shunted by the LEDs in the optoisolators and their series resistors. Nevertheless, it remains within the norms laid down in the I2C specification.
Source by : streampowers
Morning Alarm Circuit Diagram Using LDR
Circuit showing a morning alarm.Here we have used a switching transistor.When the sun rise up ldr is low resistance so the ldr is conduct and a positive volt coming to the base of the Q1 there for the transistor will switch.This time the buzzer is ON . Adjust the preset control the intensity of light.Manually cut off the power.Are you interested please comment and join this site
Component Required
Resistor 4.7k preset , LDR
Transistor BC 548
Buzzer
Source by : http://www.electronics-circuits.in/2012/01/morning-alarm.html
AM Radio Receiver Using by TEA5551T
Using TEA5551T monolithic integrated radio circuit can be designed a AM radio receiver circuit which is designed for use as a portable radio receiver with headphones .
AM Radio Receiver Circuit diagram

The TEA5551T radio receiver circuit contains all is needed for a AM radio receiver circuit (a complete AM part and dual AF amplifier with low quiescent current).The TEA5551T support a input voltage range (VS) from 1.8 V to 4.5 V but the typical voltage is 3 volts .Because in most case we don’t find to buy inductors you need to build the inductors L1 , L2 , L3 . In the picture bellow you can see the construction data for these three inductors .
AM Radio Receiver Circuit diagram

The TEA5551T radio receiver circuit contains all is needed for a AM radio receiver circuit (a complete AM part and dual AF amplifier with low quiescent current).The TEA5551T support a input voltage range (VS) from 1.8 V to 4.5 V but the typical voltage is 3 volts .Because in most case we don’t find to buy inductors you need to build the inductors L1 , L2 , L3 . In the picture bellow you can see the construction data for these three inductors .
Subscribe to:
Posts (Atom)