Showing posts with label relay. Show all posts
Showing posts with label relay. Show all posts

Monday, July 29, 2013

2008 Mercury Sable Passenger Compartment Fuse Panel and Relay Code Diagram


If you found electrical components are not working in a vehicle, a fuse may have blown, so check the appropriate fuses before replacing any electrical component. You can identify the blown fuse by the broken wire within the fuse. The following schematic / diagram shows the location of The 2008 Mercury Sable Passenger Compartment Fuse Panel and Relay. The fuse panel and relay of the 2008 Mercury Sable are located under the instrument panel to the left of the steering wheel.



Always replace the fuse with one that has the specified rating, if the amperage ratings of the replacing fuse is higher, A fuse with higher amperage rating can cause severe wire damage and could start a fire. The table below shows you the exact amperage rating, location and code for each fuse and relay. (fuse number, amperage rating, and circuit protected).


2008 Mercury Sable Passenger Compartment Fuse Panel and Relay Code:

Fuse
Amperage
Description of Circuit Protected

1
2
30A
15A
Smart window motor
Brake on/off switch, High-mounted brake lamp
3
15A
SDARS, Bluetooth, Family entertainment system (FES)/Rear seat control
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
30A
10A
20A
10A
10A
15A
15A
10A
7.5A
5A
10A
10A
15A
20A
20A
25A
15A
15A
15A
15A
20A
10A
10A
20A
5A
5A
5A
10A
10A
10A
5A
Spare
SPDJB logic power
Turn signals
Low beam headlamps (left)
Low beam headlamps (right)
Interior lights, Cargo lamps
Backlighting, Puddle lamps
All wheel drive
Memory seat/mirror switches, Memory module
FEPS module
Analog clock
Climate control
Spare
All power lock motor feeds, Decklid release
Spare
Moon roof
OBDII connector
Fog lamps
Park lamps, License lamps
High beam headlamps
Horn relay
Demand lamps/Interior lamps
Instrument panel cluster
Adjustable pedal switch
Radio, Radio start signal
Instrument panel cluster
Overdrive cancel switch
Compass, Automatic dimming rear view mirror
Restraint control module
Spare
AWD module
35
10A
Steering rotation sensor, FEPS, Rear park assist, Heated seat modules
36
37
38
39
40
41
42
43
44
5A
10A
20A
20A
20A
15A
10A
10A
10A
PATS module
Climate control
Subwoofer (Audiophile radio)
Radio
Spare
Mic mirror, Moon roof, Front lock switches, Radio
Spare
Spare
Spare
45
5A
Relay coils: PDB, Auxiliary A/C, Front and rear wipers, Front blower motor
46
7.5A
Occupant Classification Sensor (OCS), Passenger Airbag Deactivation Indicator (PADI)
47
48
30A CB*
-
Power windows
Delayed accessory relay



* CB: Circuit Breaker
Read More..

Tuesday, July 2, 2013

PIC Controlled Relay Driver

This circuit is a relay driver that is based on a PIC16F84A microcontroller. The board includes four relays so this lets us to control four distinct electrical devices. The controlled device may be a heater, a lamp, a computer or a motor. To use this board in the industrial area, the supply part is designed more attentively. To minimize the effects of the ac line noises, a 1:1 line filter transformer is used.

PIC-Controlled-Relay Driver Final
The transformer is a 220V to 12V, 50Hz and 3.6VA PCB type transformer. The model seen in the photo is HRDiemen E3814056. Since it is encapsulated, the transformer is isolated from the external effects. A 250V 400mA glass fuse is used to protect the circuit from damage due to excessive current. A high power device which is connected to the same line may form unwanted high amplitude signals while turning on and off. To bypass this signal effects, a variable resistor (varistor) which has a 20mm diameter is paralelly connected to the input.
 Controller-Schematic Circuit

Another protective component on the AC line is the line filter. It minimizes the noise of the line too. The connection type determines the common or differential mode filtering. The last components in the filtering part are the unpolarized 100nF 630V capacitors. When the frequency increases, the capacitive reactance (Xc) of the capacitor decreases so it has a important role in reducing the high frequency noise effects. To increase the performance, one is connected to the input and the other one is connected to the output of the filtering part.

Supply-Schematic circuit

After the filtering part, a 1A bridge diode is connected to make a full wave rectification. A 2200 uF capacitor then stabilizes the rectified signal. The PIC controller schematic is given in the project file. It contains PIC16F84A microcontroller, NPN transistors, and SPDT type relays. When a relay is energised, it draws about 40mA. As it is seen on the schematic, the relays are connected to the RB0-RB3 pins of the PIC via BC141 transistors. When the transistor gets cut off, a reverse EMF may occur and the transistor may be defected. To overcome this unwanted situation, 1N4007 diodes are connected between the supply and the transistor collectors. There are a few number of resistors in the circuit. They are all radially mounted. Example C and HEX code files are included in the project file. It energizes the next relay after every five seconds.

The components are listed below.
1 x PIC16F84A Microcontroller
1 x 220V/12V 3.6VA (or 3.2VA) PCB Type Transformer (EI 38/13.6)
1 x Line Filter (2x10mH 1:1 Transformer)
4 x 12V Relay (SPDT Type)
4 x BC141 NPN Transistor
5 x 2 Terminal PCB Terminal Block
4 x 1N4007 Diode
1 x 250V Varistor (20mm Diameter)
1 x PCB Fuse Holder
1 x 400mA Fuse
2 x 100nF/630V Unpolarized Capacitor
1 x 220uF/25V Electrolytic Capacitor
1 x 47uF/16V Electrolytic Capacitor
1 x 10uF/16V Electrolytic Capacitor
2 x 330nF/63V Unpolarized Capacitor
1 x 100nF/63V Unpolarized Capacitor
1 x 4MHz Crystal Oscillator
2 x 22pF Capacitor
1 x 18 Pin 2 Way IC Socket
4 x 820 Ohm 1/4W Resistor
1 x 1K 1/4W Resistor
1 x 4.7K 1/4W Resistor
1 x 7805 Voltage Regulator (TO220)
1 x 7812 Voltage Regulator (TO220)
1 x 1A Bridge Diode


http://www.ecircuitslab.com
Read More..