Showing posts with label code. Show all posts
Showing posts with label code. Show all posts
Monday, July 29, 2013
2008 Mercury Sable Passenger Compartment Fuse Panel and Relay Code Diagram
If you found electrical components are not working in a vehicle, a fuse may have blown, so check the appropriate fuses before replacing any electrical component. You can identify the blown fuse by the broken wire within the fuse. The following schematic / diagram shows the location of The 2008 Mercury Sable Passenger Compartment Fuse Panel and Relay. The fuse panel and relay of the 2008 Mercury Sable are located under the instrument panel to the left of the steering wheel.
Always replace the fuse with one that has the specified rating, if the amperage ratings of the replacing fuse is higher, A fuse with higher amperage rating can cause severe wire damage and could start a fire. The table below shows you the exact amperage rating, location and code for each fuse and relay. (fuse number, amperage rating, and circuit protected).
2008 Mercury Sable Passenger Compartment Fuse Panel and Relay Code:
Fuse | Amperage | Description of Circuit Protected |
| 1 2 | 30A 15A | Smart window motor Brake on/off switch, High-mounted brake lamp |
3 | 15A | SDARS, Bluetooth, Family entertainment system (FES)/Rear seat control |
| 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 | 30A 10A 20A 10A 10A 15A 15A 10A 7.5A 5A 10A 10A 15A 20A 20A 25A 15A 15A 15A 15A 20A 10A 10A 20A 5A 5A 5A 10A 10A 10A 5A | Spare SPDJB logic power Turn signals Low beam headlamps (left) Low beam headlamps (right) Interior lights, Cargo lamps Backlighting, Puddle lamps All wheel drive Memory seat/mirror switches, Memory module FEPS module Analog clock Climate control Spare All power lock motor feeds, Decklid release Spare Moon roof OBDII connector Fog lamps Park lamps, License lamps High beam headlamps Horn relay Demand lamps/Interior lamps Instrument panel cluster Adjustable pedal switch Radio, Radio start signal Instrument panel cluster Overdrive cancel switch Compass, Automatic dimming rear view mirror Restraint control module Spare AWD module |
35 | 10A | Steering rotation sensor, FEPS, Rear park assist, Heated seat modules |
| 36 37 38 39 40 41 42 43 44 | 5A 10A 20A 20A 20A 15A 10A 10A 10A | PATS module Climate control Subwoofer (Audiophile radio) Radio Spare Mic mirror, Moon roof, Front lock switches, Radio Spare Spare Spare |
45 | 5A | Relay coils: PDB, Auxiliary A/C, Front and rear wipers, Front blower motor |
46 | 7.5A | Occupant Classification Sensor (OCS), Passenger Airbag Deactivation Indicator (PADI) |
| 47 48 | 30A CB* - | Power windows Delayed accessory relay |
* CB: Circuit Breaker
Saturday, July 6, 2013
Morse Code Beacon Keyer
This circuit stores a single morse code message as bits in an EPROM chip, the message is sent to a relay which can key a CW transmitter. The keyer can output either a one-shot message such as "CQ DX DE CALLSIGN", or a continuous message. The continuous mode is useful for making low power (QRP) beacons. A One-shot message is controlled by the start/stop buttons, a continuous message is sent by turning on the free run switch. EPROMs other than the 2732 can be used if suitable changes are made to the circuit. For larger EPROMs, just ground the higher order address input lines on the EPROM chip, and wire the appropriate chip select pins for outputs enabled and chip selected.

It is also possible to store more than one message in different banks of a larger EPROM, for instance, if a 2764 part were used, the A12 address line could be used to select the upper or lower message.
Theory
CMOS Nor gates U1c and U1d form a gated astable clock oscillator, the frequency can be adjusted by potentiometer VR1. Gates U1a and U1b form the run/stop flip-flop. In one-shot mode, this is activated by pressing the start switch, and deactivated either by pressing the stop switch, or by the end of message signal that comes from the EPROM d1 line.
The clock oscilator causes U2, a binary counter, to step through some of an 11 bit binary count. This sequence is used to step through the addresses on EPROM U3. Morse code data is stored in the EPROM d0 bit, it is used to turn on and off Q1 and RL1, the keying relay. At the end of a one-shot message, a single 1 bit arrives on U3 pin d1, causing the run/stop flip-flop to turn off, and resetting the U2 counter to zero. D1, C2 and R4 cause U2 to reset when the power is applied. R5 is used to prevent the U3 d1 line from being shorted to +5v when the stop switch is pressed.
Programming the EPROM
I have written a C language program called cw2hex that is used to convert a sequence of ASCII characters into a hex data image that can used for programming the EPROM chip that is used in this circuit. The program takes text input and produces an Intel Hex format file as output. The hex file should be readable by most modern EPROM programmers.
The C source code and Unix Makefile are in the file cw2hex.tar.gz (tar.gzip). A DOS executable version of the code is available as cw2hex.exe. It should be possible to compile cw2hex.c on any machine with a C compiler. The C program source files are available if you want to look at the code from your web browser.
Theory
CMOS Nor gates U1c and U1d form a gated astable clock oscillator, the frequency can be adjusted by potentiometer VR1. Gates U1a and U1b form the run/stop flip-flop. In one-shot mode, this is activated by pressing the start switch, and deactivated either by pressing the stop switch, or by the end of message signal that comes from the EPROM d1 line.
The clock oscilator causes U2, a binary counter, to step through some of an 11 bit binary count. This sequence is used to step through the addresses on EPROM U3. Morse code data is stored in the EPROM d0 bit, it is used to turn on and off Q1 and RL1, the keying relay. At the end of a one-shot message, a single 1 bit arrives on U3 pin d1, causing the run/stop flip-flop to turn off, and resetting the U2 counter to zero. D1, C2 and R4 cause U2 to reset when the power is applied. R5 is used to prevent the U3 d1 line from being shorted to +5v when the stop switch is pressed.
Programming the EPROM
I have written a C language program called cw2hex that is used to convert a sequence of ASCII characters into a hex data image that can used for programming the EPROM chip that is used in this circuit. The program takes text input and produces an Intel Hex format file as output. The hex file should be readable by most modern EPROM programmers.
The C source code and Unix Makefile are in the file cw2hex.tar.gz (tar.gzip). A DOS executable version of the code is available as cw2hex.exe. It should be possible to compile cw2hex.c on any machine with a C compiler. The C program source files are available if you want to look at the code from your web browser.
Subscribe to:
Posts (Atom)
