Showing posts with label flasher. Show all posts
Showing posts with label flasher. Show all posts
Thursday, July 11, 2013
High intensity LED Warning Flasher Circuit Diagram
This circuit was designed as a warning flasher to alert road users to dangerous situations in the dark. Alternatively, it can act as a bicycle light (subject to traffic regulations and legislation). White LEDs only are recommended if the circuit is used as a bicycle front light (i.e. for road illumination) and red LEDs only when used as a tail light. During the day, the two 1.6-V solar cells charge the two AA batteries. In darkness, the solar cell voltage disappears and the batteries automatically power the circuit.
High-intensity LED Warning Flasher Circuit Diagram

The flash frequency is about one per second and the LED on-time is about 330 ms. The duty cycle should enable the batteries to power the circuit over night. The circuit is composed of three parts. Under normal daylight conditions the batteries are charged through diode D4. In darkness, pnp transistor T1 is switched on, supplying battery current to the second part, a low-frequency oscillator comprising T2 and T3.The third part is the LED driver around T4.
It conducts and switches on the LEDs D1-D2-D3 when the collector voltage of T3 swings high. Two LEDs (D1, D2) are 20,000-30,000 mcd high-brightness yellow types and one (D3) is a normal 3-mm red LED for control purposes. Of course it is possible to increase the number of LEDs to obtain higher brightness. However you will run into limitations regarding the maximum collector current of transistor T4. For really high power applications a MOSFET transistor is suggested instead of the common or garden BC547B.
Author: Jose Luis Basterra - Copyright: Elektor
Friday, April 12, 2013
Micro Flasher Circuit Using 555IC
This is a simple and compact flasher circuit that can be used where ever a flashing LED is needed. The circuit finds application in flashing beacons, alarms automobile and more. The circuit is nothing but an astable multi vibrator based on IC NE 555 (IC1). This is the figure of the circuit.

The frequency of the oscillation depends on the values of R1, R2, R3 and C2. The LED glows when the out put (pin3) of IC1 goes high. The IC1 NE 555 can easily drive a LED. The resistor R4 acts as a current limiter for LED. The circuit is powered by a 6V battery or 6V DC power supply. If you don’t need frequent changes in the flashing rate use a preset for R2 and set it for the required rate. The capacitor C2 must be rated 10V.

The frequency of the oscillation depends on the values of R1, R2, R3 and C2. The LED glows when the out put (pin3) of IC1 goes high. The IC1 NE 555 can easily drive a LED. The resistor R4 acts as a current limiter for LED. The circuit is powered by a 6V battery or 6V DC power supply. If you don’t need frequent changes in the flashing rate use a preset for R2 and set it for the required rate. The capacitor C2 must be rated 10V.
Thursday, April 4, 2013
Car Bulb Power Flasher
Derived from the Two-wire Lamp Flasher design, hosted on RED Free Circuit Designs since 1999, this astonishingly simple circuit allows one or two powerful 12V 21W car bulbs to be driven in flashing mode by means of a power MosFet.
Devices of this kind are particularly suited for road, traffic and yard alerts and in all cases where mains supply is not available but a powerful flashing light is yet necessary.
Circuit Diagram:
Car Bulb Power Flasher Circuit Diagram
| Parts | Description |
| R1 | 6.8K |
| R2 | 220K |
| R3 | 22K |
| C1 | 100uF-25V |
| C2 | 10u-25V |
| D1 | 1N4002 |
| Q1 | BC557 |
| Q2 | IRF530 |
| LP1 | 12V-21W Car Filament Bulb (See Notes) |
| SW1 | SPST Switch (3 Amp minimum) |
Notes:
- Flashing frequency can be varied within a limited range by changing C1 value.
- As high dc currents are involved, please use suitably sized cables for battery and bulb(s) connections.
Source : www.redcircuits.com
Subscribe to:
Posts (Atom)